Ninebot KickScooter MAX G2 - Electric scooter SEGWAY - Free user manual and instructions

USER MANUAL Ninebot KickScooter MAX G2 SEGWAY

Right Direction Indicator Handlebar Horn Button Brake Lever Left Direction Indicator Front Reflector Electronic Throttle Snap Hook Dashboard & Power Button Headlight Direction Indicator Switch Stem Safety Button Side Reflector Quick-release Lever Folding Mechanism Horn Front Shock Absorber Front Fender Front Fork Charge Port Drum Brake Footboard Buckle Rear Fender Tail light & Brake Light & Reflector Kickstand Battery Compartment Rear Shock Absorber Hub Motor Insurance Plate Area

Dashboard & Power Button

Speedometer Headlight Left Direction Indicator Icon Bluetooth 89 SD ECO 0 S Right Direction Indicator Icon Speed Mode Walk Mode Battery Level Power Button

Power Button: Press the button to power on; press and hold the button for 3 seconds to power off. When the Kick Scooter is on, press the

Speedrometer: I displays the current speed of the slope, as well as error rates.

Direction Indicator: When running left or right, press the “+” (left) or “-” (right) switch on the direction indicator switch. Then the

direction indicator will have regularly which can be turned off by pressing the corresponding switch again.

Walk Mode: Max speed = 5 km/h (3.1 mph)

The height and light are always on and can't be turned off.

* How to enable in the Segway-Ninebot app. Settings > Walk Mode.

speck mode. HRS are three modes available. Top 9,000 settings.

Mode	Model	Max G2 DMax G2 E
ECO (Energy-saving mode)		15 km/h (9.3 mph)
D (Standard mode)		20 km/h (12.4 mph)
S (Sport mode)		25 km/h (15.5 mph)

Bluetooth: It indicates that the controller has been successfully connected to the mobile device.

Battery Level: The total battery level equals 0 bars.

* The battery power is very low when the first battery bar is red. Please charge your KickScaler immediately.

② Specifications

	Item Parameter
Product	Name	Nimbot Kick Scooter Max G2
	Model	05.501E	051501D
	Length x Width x Light	Approx. 1210 x 570 x 125" mm (47.6 x 22.7 x 49.8 m)
	Loaded Length x Width x Light	Approx. 1210 x 570 x 805 mm (77.6 x 22.4 x 23.9 m)
	Net Weight	Approx. 24.25 kg (53.5 lbs)
Rider	Max. Payload	120 kg (260 lbs)
	Recommended Age	16-55 years old
	Required Light	120-200 pm (311"-65")
Machine	Max Speed	Approx. 25 km/h (15.5 mph)	Approx. 20 km/h (12.4 mph)
	Theoretical Range	Approx. 70 km (43.5 miles)
	Typical Range	Approx. 50 km (31.1 miles)
	Max. Slope	Approx. 22%
	Traversols Terrain	Most of one flat road conditions and typical Belgian roads
	Operating Temperature	10 - 60°C (34 - 104°F)
	Storage Temperature	10 - 50°C (24 - 122°F); recommended 10-30°C (55-95°F)
	P Rating	IPX5
	Duration of Charging	Approx. 6 h
Battery	Nominal Voltage	36 V =
	Max. Charging Voltage	42 V =
	Charging Ambient Temperature	0-60°C (32-104°F)
	Nominal Capacity	15.3 Ah
	Nominal Energy	561 Wh
	Battery Management System	Over-heating, short circuits, over-current, over-discharge and over-charge protection
Motor	Nominal Power	0.45 kW, 250 W
	Max. Power	0.9 kW, 900 W
Charger	Model	NR.4200.0270
	Type Bulk-in
	Output Power	0.128 kW, 121.8 W
	Input Voltage	100 - 240 V - 50 - 60 Hz, 2.0 A MAX
	Max. Output Voltage	42 V =
	Output Current	2.9 A
Tire	Fine Pressure	42 - 48 psi
	Lines	10 inch Tubolcs Self-soiling Tire

1. Theoretical Range: Tested while using a utility battery, 75 kg (300 lb load, 260, 47°F), at the same at 16 km/h (9.9 mph) on average on pavement
   Typical Rango: Tarent while rising with a full barley, 25 kg (60 lbs) part, 95°C (37°F), or the max spread on payment
   Some of the factors that affect range in order speed, less, number of starts and stops, ambient (temperature, etc.

③ Certifications

The battery compiles with UN 38.3.

European Union Compliance Statement Important WEEE Information

This symbol on the product or on its packaging indicates that used electrical and electronic products should not be mixed with unsorted municipal waste. For proper treatment, it is your responsibility to dispose of your waste equipment by arranging to return it to designated collection points.

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.

Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation. Please contact your local authority for further details of your nearest designated collection point.

Battery recycling information for Users

This symbol means that batteries and accumulators, at their end-of-life, should not be mixed with unsorted municipal waste. Your participation is an important part of the effort to minimize the impact of batteries and accumulators on the environment and on human health. For proper recycling you can return this product or the batteries or accumulators it contains to your supplier or to a designated collection point.

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.

Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation there are separate collection systems for used batteries and accumulators.

Please, dispose of batteries and accumulators correctly at your local community waste collection/recycling center.

Radio Equipment Directive

Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product listed in this section comply with the essential

requirements and other relevant provisions of the Radio Equipment Directive 2014/53/EU.

Restriction of the use of certain hazardous substances (RoHS) Directive

Ninebot (Changzhou) Tech Co., Ltd. hereby declares the whole product including parts (cables, cords, and so on) meets the requirements of RoHS Directive 2011/65/EU and amendment Commission Delegated Directive (EU) 2019/863 on the restriction of the use of certain hazardous substances in electrical and electronic equipment ("RoHS recast" or "RoHS 2.0").

Machinery Directive

Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of the Machinery Directive 2006/42/EC.

EU Authorised Representative:

Segway Ninebot Europe

Dynamosstraat 7, 1014 BN Amsterdam, The Netherlands.

Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product model: DS1501F, OS1501D comply with the essential requirements and other relevant provisions of the Radio Equipment Directive 2014/53/EU, the machinery directive 2006/42/EC, and the RoHS Directive 2011/65/EU and amendment Commission Delegated Directive (EU) 2015/863.

The declaration of conformity can be viewed at the following address: https://eu-en.segway.com/instruction-manuals

UK Compliance Statement

Radio Equipment Regulations 2017

Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.

The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012

Ninebot (Changzhou) Tech Co., Ltd, hereby declares the whole product including parts (cables, cords, and so on) meets the requirements of The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.

Supply of Machinery (Safety) Regulations 2008

Ninebot (Changzhou) Tech Co., Ltd, hereby declares that the product listed in this section comply with the essential requirements and other relevant provisions of The Safety of Supply of Machinery (Safety) Regulations 2008.

UK Authorised Representative

UKCA Experts Ltd.

Dept 302, 43 Owston Road Carcroft, Doncaster, DNB 8DA. United Kingdom

Ninebot (Changzhou) Tech Co., Ltd. hereby declares that the product model: 051501E complies with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017. Supply of Machinery (Safety) Regulations 2008 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.

The declaration of conformity can be viewed at the following address: www.segway.com

Bluetooth	Frequency Band(s)	2.4000-2.4835GHz
	Max. RF Power	20mW

Use of the Works with Apple badge means that a product has been designed to work specifically with the technology identified in the badge and has been certified by the product manufacturer to meet Apple Find My network product specifications and requirements. Apple is not responsible for the operation of this device or use of this product or its compliance with safety and regulatory standards.

④ Recommended Maintenance Schedule

To ensure safe riding, day to day care and regular maintenance are essential. You, the owner, have control and knowledge of how often you use your scooter, how hard you use it and where you use it. It is the owner's responsibility to perform regular checks and bring your scooter to authorized service center for inspection and service. Please refer to the maintenance schedule below.

Note: This maintenance schedule charges a service fee

Item Component		Maintenance Method	Every 3 months	Every 6 months or every 500 km (300 miles)	Every 1 year or every 1000 km (521 miles)	Every 2 years or every 10,000 km (9,247 miles)
Mainframe maintenance	Mainframe joints	The roof, one shaft is above the mainframe clean.			√√√
	Top pressure	Inflato tiro to 42.4S psi			√√√
	Top wear	Crock at the tiro are cracked, deformed, or significantly worn		√	√	√
	Screws on the stern top	Tighten the screws load with the handcetor and the stem. The suggested torque is 5.5±0.5 N·m	√	√	√	√
		Tighten the screws on the ankle. The suggested torque is 0.9±0.6 N·m; lighten the screws on the brake over. The suggested torque is 6.1 N·m. Tighten the screws on the stern top. The suggested torque is 8.6+0.8 N·m		√	√	√
	Screws on the flange mechanism	Tighten the flange screws of the folding hinge and the front fork. Two lateral screws at the side, the recommended torque is 18+1 N·m; fold and unfold, brouper vertical groove. The recommended torque is 12.1 N·m; fold the ordered rail, and fladen the connecting rod screws when rocking on the bike. The folding is smooth without shaking.		√	√	√
Item Component	Vermance Method	Twenty 5 months	Every 6 months or every 900 km (320 miles)	Every 1000 km (620 miles)	Every 3 years or every 10,000 km (6,294 miles)
Function inspection	Habitator	To accelerate and clearance, check if the habitator is stalled or has abnormal sounds.			√
	Front wheel maintenance	Check if the rear wheel is stalled or gets away, or the seat shall be administered.			√
	Brake adjustment	If the brake is too light/loose, use the 4 min Allen key blocker the screw on the caliper. Then slightly adjust the brake inc (decrease/increase the exposed angle), and tighten the screw again. Tool standard the root speed is 30 km/h (32.4 m/s) and the braking balance is still open.		√	√
	Drum brake	Front wheel can middle normally all head abnormal sound. Front wheel can be cracked after sourcing the brake over.		√	√
	Lightlight	Squeeze the brake level, the ball light works normally		√	√
	Headlight	Check the headlight and see it lights regularly.		√	√
	Direction indicators	To pick the direction indicator button to the ball light engine, help check if the direction indicators on the ball/right side flash normally.		√	√
	Dashboards	"Save on the sounder, the dashboard works properly.		√	√
	Hot	"Keep the horn button and the sound is loud.		√	√
	Throttle	Press and hold the throttle fan release checking to access them and consideration. Note: Replace it, check of the throttle will back to the pull-on.		√	√

Item Component		Valence Method	Every 3 months	Every 6 months or every 500 km (50 miles)	Every 1 year or every 1000 km (571 miles)	Every 3 years or every 10,000 km (6,204 miles)
Function inspection	Full selection	After connecting with the Sogway Nindcholt app:1) Update the remote to the latest version2) Check if the notification of the corresponding error scope and possible causes will prompt when the scooter detects an error		√	√	√
	Charging	Change the socket:1) Check if the current battery power displays on the next brand.2) Check the LED indicator on the battery change.Charging red, Fully charged, green		√	√	√
	Control buttons	Press or toggle the button 3 times without failure		√	√	√
	Turning	Last with elt turns and night turns (the steering angle is 60°). No resistance or lag when turning			√	√
Important parts	Battery assembly	The battery need to be replaced when it is changed and occurs for 500 times of the total mine age is more than 10,000 km (8.1 mmHg).Note: It is recommended to charge once every 60 days on long term storage.				√
	Controller	After 5 years' or 10,000 km 3 (6,214 miles) ring, the abnormal part of the vehicle roller have to be replaced immediately.
	Hub motor
Functional parts	Rear wheel assembly
	Throttle & brakes lever
	Front fork assembly
	Fulking mechanism
	Drumbroke
	Door board Cover

⑤ Trademark

Ninebot is the trademark of Ninebot (Beijing) Tech Co., Ltd: Segway and the Rider Design are the registered trademarks of Segway Inc., App Store, Apple Logo, Apple, Apple Find My, Apple Watch. Find My, iPhone, iPad, iPadOS, Mac, macOS and watchOS are trademarks of Apple Inc. iOS is a trademark of Cisco and is used under license. Android, Google Play and the Google Play logo are trademarks of Google LLC. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Segway-Ninebot is under license. Other trademarks and trade names are those of their respective owners.

The KickScooter is covered by relevant patents. For patent information, go to http://www.segway.com

We have attempted to include descriptions and instructions for all the functions of the KickScooter at the time of printing. However, due to constant improvement of product features and changes of design, your KickScooter may differ slightly from the one shown in this document. Scan the QR code or visit the Apple App Store (iOS) or the Google Play Store (Android) to download and install the App.

Please note that there are multiple Segway and Ninebot models with different functions, and some of the functions mentioned herein may not be applicable to your unit. The manufacturer reserves the right to change the design and functionality of the KickScooter product and documentation without prior notice.

© 2023 Ninebot (Beijing) Tech Co. Ltd. All rights reserved.

(※The Segway-Ninebot App can support KickScooter with built-in Bluetooth)

5 Common Failures

	Possible causesError code Solution
10 Bluetooth communication failure	Check the connection of dashboard communication wire and control cable, or contact after sales service or an authorized dealer.
11	Abnormal IA phase current sampling of motor. Please contact after-sales service or an authorized dealer.
12	Abnormal IB phase current sampling of motor. Please contact after sales service or an authorized dealer.
13	Abnormal IC phase current sampling of motor. Please contact after sales service or an authorized dealer.
14 Abnormal throttle hall sampling	Check whether the throttle is pressed when powered on, or contact after-sales service or an authorized dealer.
15 Abnormal broke hall sampling	Check whether the broke lever is squeezed when powered on, or contact after sales service or an authorized dealer.
18 Abnormal motor hall signal	Check whether the hall socket is loose, or contact after-sales service or an authorized dealer.
21 Battery communication failure	Check whether the wire connected with the battery communication wire and controller is loose, or contact after-sales service or an authorized dealer.
23 Default battery SN Please contact after sales service or an authorized dealer.
24 Abnormal default voltage	Check whether the connection wire of battery to controller is loose or contact after-sales service or an authorized dealer.
26 Abnormal data writing/reading please contact after sales service or an authorized dealer.
31 Incorrect PCI I/O operation Please contact after-sales service or an authorized dealer.
38 Default KickScooter SN Check whether KickScooter still keeps default SN.
39 Abnormal battery temperature	Check the working environment of battery, or contact after sales service or an authorized dealer.
40 Abnormal controller NTO	Over heated control on, or contact after sales service or an authorized dealer.
71 Abnormal motor NTO Please contact after sales service or an authorized dealer.
45	Abnormal mother wire current sampling. Please contact after sales service or an authorized dealer.

⑦ Wiring Diagram

graph TD
    A["Headlight"] --> B["Dashboard"]
    B --> C["Controller"]
    C --> D["Battery"]
    C --> E["Motor Rear LightHorn"]
    C --> F["Built-in Charger"]
    C --> G["AC Charge Port"]
    B --> H["Direction Indicator Switch + Horn"]
    B --> I["Brake"]
    B --> J["Left Direction Indicator"]
    B --> K["Right Direction Indicator"]
    B --> L["Throttle"]

① Diagramme

Amsterdam, The Netherlands

1. St. E: We are the most important studies that are general letters, so then the strongest letters we see

Amsterdam, The Netherlands

BN Amsterdam, The Netherlands

4 Recommended Maintenance Schedule

1yo spaceromy, Macsyl and zocokos by 63-54-17, 11 p.m.

R. R. R. R. R.

Amsterdam, The Netherlands

Electric Dash R

Barra

Veiligheidsknop

Reflector zijkant

Quick-releasehendel

Vouwmechanisme

Claxon

Schokdemper voor

Voorspatbord

Voorvork Voorkant

Trommelrem

k Schijf

Zócalo

Standaard

Accucompartiment

Schokdemper achter

Naafmotor

Achterkant

----Fender

Achterlicht

& Reflector

Verzekering

BUTU

Dashboard & Stroom Knop

Walk Modus: Max, stoned is 0 km/h (3.1 mph).

Segway-Ninebot Europe

Radio Equipment Regulations 2017

Supply of Machinery (Safety) Regulations 2008

Segway-Ninebot Europe